The 1-2 punch is now here!

1. Stop existing rust in its tracks with our easy to use Industrial Rust Converter.

2. Prevent future corrosion from salt with Salts Gone™.

A little product goes a long way. A 32 oz bottle will do over 220 square feet of application. 

To Use:

1. Thoroughly rinse area to be treated with Salts Gone™ to remove any salt from surface.

2. Wire wheel or otherwise remove all loose rust from surface.

3. Blow surface clean to remove any dust.

4. Shake Rust Converter bottle well to mix.

5. Pour amount needed in a separate container (DO NOT use directly out of this package as contamination will occur resulting in product hardening).

6. Brush, roll or spray Rust Converter on area to be treated. Thoroughly work it into surface in a circular motion. Deeply penetrate all areas of active corrosion.

7. Converter will turn from white to black in areas affected by rust.

8. If areas are missed with first application, wait 30 minutes before re-coating over the same area.

9. Product will dry within 30 minutes.

10. Product will fully cure in 24 hours.

11. If a topcoat is desired, apply after product is fully cured.

• Automotive
  
• Fishing Reels
  
• Boat Trailers
  
• BBQ Grills, Light Fixtures etc. around the house
  

Sprayer comes with 4 AA Batteries installed

1 Gallon of ready to use mixture 

Packaging and sprayer can be reused and refilled with any size Salts Gone™ concentrate

15 minute continue run time out of each gallon

Spray nozzle is adjustable for wide spray or "jet" stream

For use with 5 gallon pails of Salts Gone™ or larger

Wirelessly turn your Salts Gone™ on and off with the touch of a button!

Manual switch also installed on box.

Adjust the flow of Salts Gone™.

Run multiple hoses.

• Flush motors while rinsing boat
• Use sprinkler on undercarriage of vehicle while rinsing the outside

Injects Salts Gone™ into any garden hose connection. No pressure washer or other nozzles required.

System needs a standard 110V power outlet (GFCI), garden hose into box and garden hose out of box. 

Simply leave it setup and system will pull out of a 5 gallon bucket. This remote controlled injector box makes using Salts Gone™ easier than ever. Easy to buy in bulk, never refill a hose end sprayer and never need to get off the boat to grab more!

It takes only about 15 seconds to switch between Salts Gone™ and water. 

Install in just a few minutes and is just 4 screws. Box will come assembled and ready to hook to power and water. 

Improvements from original wireless box include:

• Controllable flow rate of Salts Gone™
• Ability to add a "T" or "Y" out of box to run multiple hoses
• Power switch located on box in addition to wireless remote
• Standard power cord that fits in any outlet (Inverter in box not on plug)
• Larger indicator light
• Pressure switch on pump so it can be left in on position with no damage to pump
• Larger pump to pull from higher distance
• Ideal for commercial and industrial settings and applications

*Please note for some high pressure water spigots an additional item will be needed on the inlet side of your hose. A simple screw on water pressure regulator ($20) to allow for full flow of the water, but reduce the pressure generated from the spigot. This is not needed by most customers, but will be needed by some. 

The 1-2 punch is now here!

1. Stop existing rust in its tracks with our easy to use Industrial Rust Converter.

2. Prevent future corrosion from salt with Salts Gone™.

A little product goes a long way. A Gallon  will do over 600 square feet of application. 

To Use:

1. Thoroughly rinse area to be treated with Salts Gone™ to remove any salt from surface.

2. Wire wheel or otherwise remove all loose rust from surface.

3. Blow surface clean to remove any dust.

4. Shake Rust Converter bottle well to mix.

5. Pour amount needed in a separate container (DO NOT use directly out of this package as contamination will occur resulting in product hardening).

6. Brush, roll or spray Rust Converter on area to be treated. Thoroughly work it into surface in a circular motion. Deeply penetrate all areas of active corrosion.

7. Converter will turn from white to black in areas affected by rust.

8. If areas are missed with first application, wait 30 minutes before re-coating over the same area.

9. Product will dry within 30 minutes.

10. Product will fully cure in 24 hours.

11. If a topcoat is desired, apply after product is fully cured.

Easily share Salts Gone with anybody! Great gift for the buddy that takes you out on their boat!

Gift cards are 100% electronic and you will receive an email link with the card. No physical card will be mailed out.